View unanswered posts | View active topics It is currently Thu Mar 28, 2024 2:24 pm



Reply to topic  [ 44 posts ]  Go to page Previous  1, 2, 3, 4, 5  Next
 Project CRD MJ: 
Author Message

Joined: Sun Dec 25, 2011 1:41 pm
Posts: 126
Got a shell for the MJ, its a brahma which means its kinda cheap, maybe in the future if I find a nice leer that I like I will upgrade, but for now this is fine by me.
Image
Image
Image
Image

The holy grail of MJ 97+ door panels:
Image

Scored a set of seats from a 2 door......the seats themselves are pretty much junk, but they have the tilt mechanisms which can be installed into just about every other jeep seat(could install them in heated leather seats for example).
Image


Fri Mar 02, 2012 1:24 pm
Profile

Joined: Sun Dec 25, 2011 1:41 pm
Posts: 126
I got a wildernest topper last year in august of 2017. And then finally got rid of the other shell on CL. Turns out the old one fit a longbed toyota truck perfect.

Image
Image
Image


Sun Jan 28, 2018 5:59 pm
Profile

Joined: Sun Dec 25, 2011 1:41 pm
Posts: 126
New as of 3-NOV-2017:

I ordered a pair of metric ton leaf springs with ~3" or so of lift. Took a long damm time to come in but they finally arrived last night.

I have a set of ruff stuff SUA perches that I will use to mount these up to a KJ 8.25 from my 05 parts CRD.

http://www.ruffstuffspecialties.com/cat ... -WIYP.html



The 8.25 I am using has a limited slip and 3.73s which is a good match for the CRD powerband.


Sun Jan 28, 2018 5:59 pm
Profile

Joined: Sun Dec 25, 2011 1:41 pm
Posts: 126
Rolled the MJ into the garage and started prepping the KJ axle, got the KJ brackets - lower control arm, shock mount, and spring pad cutoff, and I am half done grinding the tube smooth.

Brackets to cutoff:

Image

Image

Image

Spring pad cleaned up:

Image

Everything cutoff:

Image

Image


Sun Jan 28, 2018 6:01 pm
Profile

Joined: Sun Dec 25, 2011 1:41 pm
Posts: 126
In preparation for installing the axle I sprayed the leaf springs. They were basically bare steel, or one step above it. So I prepped them by cleaning with Acetone and a microfiber rag. I had a ton of high temp rustoleum black around so I used that, hit the leaves with a bunch of coats of. Might not be the best prep or cleanup or even paint for the long term, but its gotta be better than bare and I'll its under the jeep anyway.

Image

Image

Image

Image

Image

Image


Sun Jan 28, 2018 6:02 pm
Profile

Joined: Sun Dec 25, 2011 1:41 pm
Posts: 126
So I made a video showing some things I ran into with the spring......
https://youtu.be/4aUsUiwlxrk

I think I'm going to try and push to have some more videos go along with what I'm doing, youtube recently changed their rules so I am now in a push to hit 1000 subscribers, I have a little over 500 currently.

Shameless plug:
For any of you willing to subscribe please to help me out you can do so by clicking on:
https://www.youtube.com/channel/UCtRd0A ... irmation=1


Sun Jan 28, 2018 6:03 pm
Profile

Joined: Sun Dec 25, 2011 1:41 pm
Posts: 126
Old springs VS New.

https://youtu.be/9vq6Y7Ka3p8

I wasn't able to get the axle in, turns out I was shipped the wrong perch, so the axle wont be under it until next weekend I would guess.

https://youtu.be/-lbpswKezQs


Sun Jan 28, 2018 6:04 pm
Profile

Joined: Sun Dec 25, 2011 1:41 pm
Posts: 126
Got the new perches, got it in last night. Took a video showing the installed state and a few things about it.

Be forwarned its a little long if you are not planning to swap this axle into an MJ:

https://www.youtube.com/watch?v=QcPzZFVUUrs


Sun Jan 28, 2018 6:05 pm
Profile

Joined: Sun Dec 25, 2011 1:41 pm
Posts: 126
Finished installing the Chevy drop shackles. I got about an inch of lift out of them, I have one higher hole on the shackles I could use, but it won't give me much more lift.

This was the set I picked up, I am pleased with the quality for the price.
https://www.amazon.com/gp/product/B0106NWAJY


Image
Image

MJ shackle top(which is longer than an XJ shackle)
Image

Image

The width is a little different. I used giant cresent wrench to bend open the frame side shackle box, put the shackle in, and then bolted it tight. If I were a more patient man I would have pulled the bushing out, shaved down the width of the metal sleeve, and then bushing to make it the correct size.

Image

Likewise the other end is a little large, I picked up a couple of fender washers to take up space and then bolted it tight, again the nut and bolt pulled it closed some.

Image

Installed in lower position:

Image

Image

Image

How it sits now:

About 20" between flare bottom and wheel center. Height is OK. Might end up moving the shackle up once springs settle some.


Fri Feb 02, 2018 10:24 pm
Profile

Joined: Sun Dec 25, 2011 1:41 pm
Posts: 126
I finished cutting off the old bracket and I got the new one trimmed to fit.

Image
Image
Image
Image
Image

I finished cleaning up the floor with the wire wheel and flap disked the area where the bracket needs to be welded down. I'll hit them with some copper weld through primer before welding, then follow up with seam sealer and POR15.


Sun Feb 18, 2018 9:27 am
Profile
Display posts from previous:  Sort by  
Reply to topic   [ 44 posts ]  Go to page Previous  1, 2, 3, 4, 5  Next

Who is online

Users browsing this forum: No registered users and 8 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group
Designed by ST Software.